1/48 Republic XF-103 Thunderwarrior- projekt*

krótko mówiąc po polsku: Tutorial

Moderatorzy: kartonwork, Rafal N.

NOBI
Posty: 18
Rejestracja: śr kwie 07 2004, 9:15

1/48 Republic XF-103 Thunderwarrior- projekt*

  • Cytuj
  • zaloguj się, by polubić ten post

Post autor: NOBI »

Now I begin next project with 1/48 Republic XF-103 Thunderwarrior...all necessary line is drew on Rhino ready to make surface. Progress next

Obrazek
Best Regards
NOBI

"If the model turns into a failure -- immediately tell everyone it's a prototype"

Visit Thaipaperwork at
http://thaipaperwork.com

Visit Thaipaperwork's Blog at
http://thaipaperwork.blogspot.com/
NOBI
Posty: 18
Rejestracja: śr kwie 07 2004, 9:15

  • Cytuj
  • zaloguj się, by polubić ten post

Post autor: NOBI »

Hi There,

Update progress :) about something like canopy on top of model...first i dont know what is it. I think that should be some hole to let pilot see what is in front of aircraft...too small to be a canopy. I add it because of picture of finish model (in plastics) at http://features02.kitparade.com/xf103pb_1.htm have this thing too :) thank you very much for all advise

let's see model when finish making surface below :) strange looking craft, i think

Obrazek

Obrazek

and below is 3 views drawing i have... no cross section make me hard to make a mesh :(

Obrazek
Best Regards
NOBI

"If the model turns into a failure -- immediately tell everyone it's a prototype"

Visit Thaipaperwork at
http://thaipaperwork.com

Visit Thaipaperwork's Blog at
http://thaipaperwork.blogspot.com/
NOBI
Posty: 18
Rejestracja: śr kwie 07 2004, 9:15

  • Cytuj
  • zaloguj się, by polubić ten post

Post autor: NOBI »

Tonight I add all of panel line into surface...only decal left and then unfold :)

Obrazek
Best Regards
NOBI

"If the model turns into a failure -- immediately tell everyone it's a prototype"

Visit Thaipaperwork at
http://thaipaperwork.com

Visit Thaipaperwork's Blog at
http://thaipaperwork.blogspot.com/
NOBI
Posty: 18
Rejestracja: śr kwie 07 2004, 9:15

  • Cytuj
  • zaloguj się, by polubić ten post

Post autor: NOBI »

A little bit progress with decal on mesh

Obrazek

and compare 3 steps before unfold

Obrazek
Best Regards
NOBI

"If the model turns into a failure -- immediately tell everyone it's a prototype"

Visit Thaipaperwork at
http://thaipaperwork.com

Visit Thaipaperwork's Blog at
http://thaipaperwork.blogspot.com/
NOBI
Posty: 18
Rejestracja: śr kwie 07 2004, 9:15

  • Cytuj
  • zaloguj się, by polubić ten post

Post autor: NOBI »

Unfold nearly finish...post some progress first... only internal former and connection strip left

Obrazek
Best Regards
NOBI

"If the model turns into a failure -- immediately tell everyone it's a prototype"

Visit Thaipaperwork at
http://thaipaperwork.com

Visit Thaipaperwork's Blog at
http://thaipaperwork.blogspot.com/
NOBI
Posty: 18
Rejestracja: śr kwie 07 2004, 9:15

  • Cytuj
  • zaloguj się, by polubić ten post

Post autor: NOBI »

Update today :-) all parts arrange on letter size page. Only Connection strip left. I will post how to make connection strip from Rhino for people who interest too :-)

Obrazek
Best Regards
NOBI

"If the model turns into a failure -- immediately tell everyone it's a prototype"

Visit Thaipaperwork at
http://thaipaperwork.com

Visit Thaipaperwork's Blog at
http://thaipaperwork.blogspot.com/
Awatar użytkownika
Rutek63
Posty: 756
Rejestracja: pn paź 25 2004, 20:03
Lokalizacja: Scarsdale, NY
x 1

  • Cytuj
  • zaloguj się, by polubić ten post

Post autor: Rutek63 »

Hello,

What's the name of the process used to unwrap the model for printing? The button that you click to activate the tool that unwraps the model, what's that button called?
Obraz jest wart tysiąca słów. Model wart jest miliona.
NOBI
Posty: 18
Rejestracja: śr kwie 07 2004, 9:15

  • Cytuj
  • zaloguj się, by polubić ten post

Post autor: NOBI »

I use unrollsrf function to unwrap mesh, you can access to this function at surface > unroll Developable srf

about tutorial...i will explain how to make connection strip for my design. just a simple method and hope that my technics will helpful for modeler

first at all choose your part what you want to make strip like below

Obrazek

after that remove panel line and decal you draw out from part

Obrazek

then use only half of part to do a strip, because this is symmetry part

Obrazek

select a polyline what you want to have a strip in there and use offset curve function from curve > offset curve

Obrazek

i decide to use 5 mm strip for my model so i will offset polyline to 2.5 mm. each side

Obrazek

Obrazek

Obrazek

then draw a polyline to close all open shape

Obrazek

select polyline as show in picture below then use function array along curve from transform > array > array along curve

Obrazek

choose Distance between Item option and type 2.5 inside a box press ok

Obrazek

you will get a polyline along curve with 2.5 mm distance each line

Obrazek

offset side curve as below with 2.5 mm. distance

Obrazek

draw a polyline to close all open shape

Obrazek

make a strip in another side of part

Obrazek

select all line and mirror it

Obrazek

this is what you get

Obrazek

trim all no need line

Obrazek

Obrazek

you will get a U type strip :)

Obrazek

and you can make L type strip too

Obrazek

apologized for my poor English but i think pictures will explain all i want to say :)
Best Regards
NOBI

"If the model turns into a failure -- immediately tell everyone it's a prototype"

Visit Thaipaperwork at
http://thaipaperwork.com

Visit Thaipaperwork's Blog at
http://thaipaperwork.blogspot.com/
NOBI
Posty: 18
Rejestracja: śr kwie 07 2004, 9:15

  • Cytuj
  • zaloguj się, by polubić ten post

Post autor: NOBI »

Another progress... label and instruction is finish...can't wait to color her :)

Obrazek
Best Regards
NOBI

"If the model turns into a failure -- immediately tell everyone it's a prototype"

Visit Thaipaperwork at
http://thaipaperwork.com

Visit Thaipaperwork's Blog at
http://thaipaperwork.blogspot.com/
NOBI
Posty: 18
Rejestracja: śr kwie 07 2004, 9:15

  • Cytuj
  • zaloguj się, by polubić ten post

Post autor: NOBI »

coloring start...not finish yet but test build soon :)

Obrazek
Best Regards
NOBI

"If the model turns into a failure -- immediately tell everyone it's a prototype"

Visit Thaipaperwork at
http://thaipaperwork.com

Visit Thaipaperwork's Blog at
http://thaipaperwork.blogspot.com/
ODPOWIEDZ